{"product_id":"mazda-rx-7-front-drift-angle-lock-kit","title":"Mazda RX-7 Front Drift Angle Lock Kit","description":"\u003cul\u003e\r\r\n\u003cli\u003e\r\r\n\u003cp\u003eMazda RX7 Wisefab Lock Kit\u003c\/p\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003eFor Mazda RX7 FD (1992 – 2002).\u003c\/li\u003e\r\r\n\u003cli\u003eSteering rack at original position can be used or it can be lowered 10mm if needed.\u003c\/li\u003e\r\r\n\u003cli\u003e 62 degrees of lock, parallel steering. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment.\u003c\/li\u003e\r\r\n\u003cli\u003eAdjustable lock stopper.\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003eAll the steel components on Wisefab RX7 front suspension are from high strenght steel, including sheetmetal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003eHigher roll center (RC). RX7 has a double A-arm suspension, which is a very good starting point for a racecar. Lowering the car would increase performance and handling, but this would mess up the original factory designed kinematics. It lowers the roll center and increases camber gain.  On Wisefab knuckle, both joints are dropped, which brings the front RC up on lowered car, providing higher roll stiffness,  good camber control and minimal bump steer with high steering angles. On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.\u003c\/li\u003e\r\r\n\u003cli\u003eSteering jacking control. During steering the car chassis is moving up and down – this is called jacking. Steering jacking is caused by combination of caster, KPI, trail and scrub. On road cars, this effect is used sometimes to balance the car or to help to turn in. During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.\u003c\/li\u003e\r\r\n\u003cli\u003eConsistent and predictable self-alignment torque. Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. \u003c\/li\u003e\r\r\n\u003cli\u003eOriginal swaybar can be used in front\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003cp\u003e\u003cb\u003eOther components, packaging and clearance.\u003c\/b\u003e\u003c\/p\u003e\r\r\n\u003cp\u003e This kit assumes coilovers to have enough clearance. \u003cbr\u003e Ride height is designed to be ~80mm from front subframe to ground\u003cbr\u003e Dependent on rim width and ET, wider fenders or fender flares would be needed.\u003cbr\u003e Inner wheel wells do not need to be modified with tire diameter up to 635mm (215\/45R17, 225\/45R17, 235\/40R17, 225\/40R18 etc). Minimum rim diameter is 17”.\u003cbr\u003e Recommended backspacing is ~135mm (7“ ET45; 8“ ET35; 9“ ET20). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.\u003c\/p\u003e\r\r\n\u003cp\u003eThe kit is designed and manufactured the way that after installation and toe adjustment it’s ready to use right away.\u003c\/p\u003e\r\r\n\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003cp\u003e \u003c\/p\u003e\r\r\n\u003cp\u003e\u003cspan\u003eOther components, packaging and clearance. \u003c\/span\u003e\u003c\/p\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003eThis kit assumes coilovers to have enough clearance.\u003c\/li\u003e\r\r\n\u003cli\u003eRide height is designed to be ~80mm from front subframe to ground.\u003c\/li\u003e\r\r\n\u003cli\u003eDependent on rim width and ET, wider fenders or fender flares would be needed.\u003c\/li\u003e\r\r\n\u003cli\u003eInner wheel wells do not need to be modified with tire diameter up to 635mm (215\/45R17, 225\/45R17, 235\/40R17, 225\/40R18 etc).\u003c\/li\u003e\r\r\n\u003cli\u003eMinimum rim diameter is 17”.\u003c\/li\u003e\r\r\n\u003cli\u003eRecommended backspacing is ~135mm (7“ ET45; 8“ ET35; 9“ ET20). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.\u003c\/li\u003e\r\r\n\u003c\/ul\u003e","brand":"AutoBan Garage","offers":[{"title":"Default Title","offer_id":47433824370826,"sku":"WFR70","price":2750.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0736\/8631\/9242\/files\/WFR70-1.jpg?v=1765231077","url":"https:\/\/www.autoban-garage.com\/products\/mazda-rx-7-front-drift-angle-lock-kit","provider":"AutoBan Garage","version":"1.0","type":"link"}