{"product_id":"toyota-gt86-front-v2-lock-kit-for-front-rack","title":"Toyota GT86 Front V2 Lock Kit for Front Rack","description":"\u003cdiv class=\"product attribute description\"\u003e\r\r\n\u003cdiv class=\"value\"\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003e65+ degrees of usable steering angle\u003c\/li\u003e\r\r\n\u003cli\u003eAdjustable Ackermann angle. You can tune your steering geometry towards positive or negative Ackermann in just a few minutes without messing up the alignment. Ackermann adjustment washers are included in the kit.\u003c\/li\u003e\r\r\n\u003cli\u003eKnuckles and control arms are made of high strength steel. All parts are machined after welding for maximum precision. \u003c\/li\u003e\r\r\n\u003cli\u003eCrMo rod ends and sphericals used instead of OEM bushings\u003c\/li\u003e\r\r\n\u003cli\u003eHigher roll center (RC)\u003cbr\u003eWith our knuckle, the ball joint is lowered, which brings the front RC up on a lowered car, providing higher roll stiffness. This allows to remove the front anti roll-bar (sway bar) that is quite difficult to package with high steering angle.\u003c\/li\u003e\r\r\n\u003cli\u003eGood camber control and minimal bump steer with high steering angle.\u003cbr\u003eOn drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber will provide very good front grip and bump steer is minimal throughout the steering range.\u003c\/li\u003e\r\r\n\u003cli\u003eSteering jacking control\u003cbr\u003eDuring drifting, when steering angle is increased, jacking is also bigger, even with the same geometry it could become a problem. We have changed the geometry in a way that doesn't cause any handling issues.\u003c\/li\u003e\r\r\n\u003cli\u003eConsistent and predictable self-alignment torque. \u003cbr\u003eCaster is not the only important parameter to provide sufficient self-alignment torque, especially at high lock. It's the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn't get stuck at full lock.\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003cp\u003eKit includes:\u003c\/p\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003ePre-set lower control arms\u003c\/li\u003e\r\r\n\u003cli\u003eKnuckles with hardware\u003c\/li\u003e\r\r\n\u003cli\u003eAssembeled tie rods\u003c\/li\u003e\r\r\n\u003cli\u003ePre-set coilover camber plates\u003c\/li\u003e\r\r\n\u003cli\u003eFront position rack relocating kit\u003c\/li\u003e\r\r\n\u003cli\u003eCrossmember supports\u003c\/li\u003e\r\r\n\u003cli\u003eInstallation guide\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003cp\u003e \u003c\/p\u003e\r\r\n\u003cp\u003eOther information:\u003c\/p\u003e\r\r\n\u003cul\u003e\r\r\n\u003cli\u003eBMW and Lexus steering rack attachments and crossmember inserts are included in the kit. To modify the crossmember some DIY cutting and welding needs to be done. Please make sure to follow the installation manual.\u003c\/li\u003e\r\r\n\u003cli\u003eThis kit assumes coilovers for enough clearance\u003c\/li\u003e\r\r\n\u003cli\u003eDependent on rim width and ET, wider fenders or fender flares are needed.\u003c\/li\u003e\r\r\n\u003cli\u003eDue to extremely wide engine bay on Subaru BRZ, we recommend using tires no bigger than 605mm (215\/40R17, 225\/40R17, 225\/35R18, 235\/35R18)\u003c\/li\u003e\r\r\n\u003cli\u003eWith tire diameter up to 635mm (215\/45R17, 225\/45R17, 235\/40R17, 225\/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.\u003c\/li\u003e\r\r\n\u003cli\u003eRecommend rim size 18\" but some 17\" might also fit.\u003c\/li\u003e\r\r\n\u003cli\u003eDepending on the rim diameter the recommended backspacing is 150-160mm (7\" ET45; 8\" ET35; 9\" ET25). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.\u003c\/li\u003e\r\r\n\u003c\/ul\u003e\r\r\n\u003c\/div\u003e\r\r\n\u003c\/div\u003e","brand":"AutoBan Garage","offers":[{"title":"Default Title","offer_id":47433826959498,"sku":"WF8601","price":2650.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0736\/8631\/9242\/files\/wisefab-toyota-gt86-v2-angle-kit-1080-3.jpg?v=1765231148","url":"https:\/\/www.autoban-garage.com\/products\/toyota-gt86-front-v2-lock-kit-for-front-rack","provider":"AutoBan Garage","version":"1.0","type":"link"}